Ipod Interface Installation 2002-2006 MINI Cooper

Abstract: This article describes Ipod interface installation.


Applies to: MINI Cooper S: 2004-2006



Installation Instructions

 

Page 1 of 10
September 2006

Audio, iPod Interface

Ver 2.0

 

These installation instructions supersede all previous versions
SUBJECT
iPod® Interface Kit – P/N 65 11 0 409 341
MODEL
MINI Cooper (R50): Select Vehicle Production 01/02 – On*
MINI Cooper-S (R53): Select Vehicle Production 03/02 – On*
MINI Convertible (R52): Select Vehicle Production 09/04 – On*
MINI Cooper-S JCW GP: Select Vehicle Production 06/06 – 09/06
* Not compatible with 6-Disc CD Changer (SA672), and/or Hands-Free Phone System.SUGGESTED INSTALLATION TIME: 0.75 Hours
Total installation time may vary depending on vehicle options and equipment.
The instructions below are developed for MINI vehicles and are not to be compared to any other existing instructions for vehicles other than MINI. No methods other than those specified in this document are to be used for installation in MINI vehicles. Left and right are determined from the driver's seat.
Carefully read all instructions and supplements before proceeding with the installation.

PARTS INFORMATION
Contents of Kit – P/N 65 11 0 409 341

Description

QTY

MINI Part Number

iPod Adapter

1

65 11 0 406 349

iPod I/F cable

1

65 11 0 393 656

iPod Radio I/F cable

1

65 11 0 411 925

Rubber Grommet

1

N/A

Wrap

1

N/A

Owner's Manual

1

65 11 0 409 344


SPECIAL TOOLS
Pin Removal Tool – 61 1 134
Crimp Tool – 408 449

Only for vehicles equipped with the Trunk Mounted 6 Disc CD Changer:

  1. • Remove 3-pin connector (X18180) and 6-pin connector (X9960) from 6 Disc CD changer.


    Warning: Failure to perform this step will
    cause the iPod Interface to
    malfunction.


*Disconnect negative battery terminal.



*Remove the following components using information available in TIS:

    1. • Drivers knee bolster (1)
    2. • Center dash face (2) (Refer to RA62 21 001)
    3. • Radio side pillars (3) (Refer to RA51 16 198)
    4. • Radio (4) (Refer to RA 65 11 030)
    5. • Glove box (5)
      |


*Remove the blue lock (1) from radio harness by releasing tab and sliding upwards, then remove following terminals (2) using AMP terminal removal tool p/n 61 1 134:


Pin #
Color
Description
9
White/Red
I-Bus
12
Brown
Ground
15
Red/Brown
KL 30
Note: Wire colors may vary depending on vehicle production changes.


*Insert pins (1) removed from radio connector into 4-pin connector (2) as follows:


Color
Location
Description
Red/green
2
KL 30
White/gray
3
I-Bus
Brown
4
KL 31
Note: Wire colors may vary depending on vehicle production changes.

*Insert locking tab (3) on 4-pin connector as shown

|


*Insert 3 rectangular pins from radio I/F cable (1) into radio harness connector (2) as follows:


Color
Location
Description
White/gray
9
I-Bus
Brown
12
KL 31
Red/green
15
KL 30

*Remove white 12-pin connector (3) from lower section of radio connector.


Note: For Cooper-S with JCW GP Kit, the white 12-pin connector is not present. |


*Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3).


*Tie factory white 12-pin connector (4) back to harness as it will not be used for this installation.
|


*Connect 4-pin connectors (1 & 2)


|

For Kits with Radio I/F Cable 65 11 0 392 142:

  1. 1. Cut original terminals off of the 3 wires (1) removed from locations 9, 12, & 15. Cut wire as close as possible to existing terminal to maintain wire length.


    *Strip 1/8" of wire shielding from 3 wires.


    *Using terminal crimping tool (BMW p/n 408 449 or Snap-on PWC47) crimp new female bullet connectors included in kit onto each of the wires from previous step.


*Insert the 3 pins (1) removed from radio connector into 4-pin connector (2) as follows:


Color
Location
Description
Red/brown
2
KL 30
White/red
3
I-Bus
Brown
4
KL 31
Note: Wire colors may vary depending on vehicle production changes. |


*Insert 3 rectangular pins from iPod harness (1) into radio harness (2) as follows:


Color
Location
Description
White/gray
9
I-Bus
Brown
12
KL 31
Red/green
15
KL 30
Note: The Violet/White wire of the iPod Harness (1) is not used for this installation.
*Remove white 12-pin connector (3) from lower section of radio connector.


Note: For Cooper-S with JCW GP Kit, the white 12-pin connector is not present. |


*Insert white 12-pin connector (1) from iPod harness (2) into lower left section of radio connector (3).


*Tie factory white 12-pin connector (4) back to harness as it will not be used for this installation.


|


*Connect 4-pin connectors (1 & 2)


|
Installation Manual P/N 01 29 0 408 519

iPod Cable – Glove Box

  1. 1. Locate and drill 5/8" (16mm) hole in glovebox.


    A = 1" (25mm)
    B = 1" (25mm)
    C = 5/8"(16mm) Ø |


*Insert iPod cable (1) through hole in glovebox as indicated.

|

Note: Split grommet as shown before placing around iPod cable in order to prevent damage to cable.

*Split grommet (1) as indicated (2) and insert grommet through hole in glovebox wall.


|
8 Installation Manual P/N 01 29 0 408 519


*The flat iPod connector (1) should be located in the glovebox and the 8-pin DIN connector (2) for the adapter box should be routed through the center console to a location behind the radio.


  1. 5. Re-connect glovebox vent tube.


  2. 6. Re-install glovebox.


|

Caution: Check for bent pins on adapter cables before attaching to iPod adapter. If pins are damaged carefully bend them back into position with a small screwdriver.

*Slide iPod adaptor (2) fully into foam wrap (1).


*Connect white "iPod" adapter cable (3) and black "Radio" adapter cable (4) to iPod adapter, making sure to connect cables in their proper location.


|


*Mount iPod interface as indicated below radio and secure with cable ties (not included).


*Re-install all components removed for installation procedure.


|

RETROFIT CODING
There is no retrofit coding required for this installation.
TROUBLESHOOTING

  1. • In iPod mode, "No Magazine" is displayed on the radio until an iPod is connected.

(refer to MINI iPod Interface Owner's Manual)
• This iPod Interface is compatible starting with the following iPod Firmware versions:

    1. o iPod with Dock Connector - SW 2.3
    2. o iPod with Click Wheel - SW 3.1.1
    3. o iPod mini - SW 4.1.1
    4. o iPod with Color display - SW 1.2.1
    5. o iPod nano - SW 1.1.1
    6. o iPod Gen5 (Video) - SW 1.1.1


If the customer's iPod has older versions of software, please advise
them to upgrade the software before connecting them to the Interface in their
MINI vehicles. (refer to MINI iPod Interface Owner's Manual)

  1. • In case of erratic behavior in iPod mode please perform the following:


  1. ???RESET the iPod – Please refer to your Owner's Manual that was included with your iPod.
  2. ???RESET the iPod Interface – Disconnect the iPod from the iPod cable (White)

and remove the black 7-Pin DIN connector from
the interface module. Wait for 10 seconds and re-
connect 7-pin DIN connector to module. Interface
RESET is complete.
10 Installation Manual P/N 01 29 0 408 519
Circuit Diagram
Key
X-1 Connection, radio (audio signal)
X-2 Connection, MPQ contacts
X-3A Connection, 4-pin
X-4 Connection, Fuse (2A)
X-5 Connection, 7-Pin DIN connector
Wire Colors
BL Blue
BR Brown
GE Yellow
GN Green
GR Gray
RT Red
SW Black
VI Violet
WS White

Related Topics

MINI Repair & Technical Literature: http://www.bentleypublishers.com/mini/

Before Performing any Work

Please read Cautions and Warnings before proceeding with any work on your vehicle

Technical Discussion Forums